Guide for Comparing Steel Barricades

Whether you are in a building, administration, or leisure, buying steel barricades necessitates some expertise with barricade characteristics and variants. While barriers seem to be typical, different aspects make more or less sense depending on your crowd management expertise. Do you require barriers that can withstand harsh weather and rain? Will they have to be able to withstand difficult terrain? Would the mob need a way to get past the barricades? Would these obstacles have to be relocated and stored, or would they be firmly fixed? While evaluating various barriers for sale, these are important factors to consider.

Before you go out and acquire steel barriers, bear the following in mind:

• Steel barriers are classified according to their external coating and foot design.
• Barricades are made to endure. When purchasing additional barriers, you must consider compatibility characteristics. Differences in welding and hooks determine compatibility, the number of barriers required, and barricade longevity.
• Learn about barricade enhancements and suitable items. Storage, swing doors, and jacket coverings may be required for any specific occasion.
• To get as much out of your investment, know more about the various ways barriers might be utilized in your sector.

Types of Steel Barricades

Galvanized in a hot-dip process

After barriers have been made and installed, they are coated in hot zinc plating to provide a rust-proof seal. Hot-dipped galvanized barriers are the finest option for usage outdoors, where they can survive severe weather conditions for a lengthy period before rust.

Pre-Galvanized

Barricades with a lighter galvanization coating were applied before fully assembled, leaving seams un-sealed. Pre-galvanized barriers are more suited to short-term interior usage since they rust less easily.

Coated in powder

Powder coating applies a uniform coating of pigment to the steel barricades, completely covering them in color coatings that are more durable than regular paint. Powder coating allows for further personalization, such as increased visibility and aesthetic synchronization for special occasions and improved weather resistance and longevity.

Bridge Feet

The bridge feet may be removed from the barricade frame for convenient storage whenever the panels are laid flat. One big bridge foot and one little bridge foot are included in each “pair” of bridge feet. The big and tiny feet enable perpendicular barriers to be built up, providing a corner where the feet may overlap without causing an obstruction. Bridge feet are advised to boost stability and sturdiness when placing roadblocks on uneven or sloped terrain. These are often utilized on uneven terrain, including grass, gravel, and small inclines or slopes.

Bridge feet are attached to a barrier using 1/4″ bolts “-20 in terms of hardware. Those screws may be found at most hardware shops.

Pros:

• On slopes and uneven ground, a wide stance gives further stability.
• Feet may be separated simply for travel and storage.

Cons:

• Feet are not connected and must be constructed prior to use.

Flat Feet

Flat feet are detachable and designed to rest flat on the ground, saving space and reducing tripping risks. On level, even surfaces, flat feet are preferable. They may be fastened to the ground for a much more permanent installation. “Pairs” of flat feet consist of two similar feet. Flat feet are attached to a barrier using 1/4″ screws “-20 in terms of hardware. Those screws may be found at most hardware shops. 

Pros:

• For a permanent installation, they may be easily drilled into surfaces.
• Feet may be separated simply for travel and storage.
• Reduce tripping dangers by taking up less surface area than bridge feet.

Cons:

• On uneven terrain, there is less stability.
• Feet are not connected and must be constructed prior to use.

Fixed Feet

To save time and effort, fixed foot barriers are advised. Barricades having fixed feet have the feet already connected, making set-up a breeze. These barriers are adaptable but could be used on flat or uneven terrain.

Pros:

• There is no need to construct the feet since they are already connected.
• Large volumes may be stacked.

Cons:

• Damaged feet cannot be replaced; the whole barrier must be repaired or rebuilt.
• In storage, frames do not lay flat.

Other noteworthy characteristics

• Every tube on a barrier is soldered all the way to all-around tube joints, ensuring that it is as firmly attached to the frames as possible.
• Whenever a tube is cut (sometimes termed a saddle cut) to fit perfectly inside the frame and afterward soldered up for a more accurate and secure connection, it is referred to as a saddle weld.
• Hooks on the sides of barriers that can effortlessly slide in and connect with comparable barricades are interlocking hooks. The graphic below might help determine whether your barriers are compatible (see Barricade Compatibility).

Compatibility with Barricades

Barricades are goods that last a long time. As a result, buyers often inquire whether their previous blockade would work with the big purchase. Although there is no certainty that a barrier will fit precisely, there seem to be a few crucial factors to consider. Check the dimensions below to be sure you’re getting the right barrier.

Extras for the Barricade

Are you looking for a more convenient method to relocate your barricades? What about putting up a gate through which people may pass? Maybe you’re looking for a fresh strategy to market your business, and your present roadblocks aren’t cutting it. Add-ons and accessories like carts, gates, and jackets provide you with additional practical alternatives while adding individual flair and design.

• Transferring and stacking barricades are done using Barricade Carts. Each cart can hold between 24-30 barriers, which saves time and space.
• Swinging Gates is a chain of interconnected barriers with apertures. These gate apertures are attached to an existing barrier and swing open and closed on wheels, making them easy to transport.
• Barricade Jackets are printed coverings that fit over the barricade’s frame. Those covers, made of heavy-duty polyester, can withstand adverse weather conditions and come in several colors, designs, fonts, and artwork to suit your specific branding demands.

Bottom Line

We believe that this detailed guide assists you in locating the barrier you need. Steel barricades are often used in entertainment, construction, government, and other industries. You’re presumably also aware that purchasing for them isn’t as straightforward as it seems.

Although all-steel barriers seem to be the same, there are significant variances between them. What may seem to be “minor” details, such as storage optimization or usage on uneven terrain, may have a big influence on the performance of a crowd control application.